KEY: BLUE ITEM # = NEW | RED ITEM # = HAZARDOUS | v OVERSIZE | * WHILE SUPPLIES LAST 97 ENGINE ACCESSORIES Item# Diameter Case 50-28481c 131/ 2" 5 50-28531c 151/ 2" 5 Repl. Parts Description Size Case 50-28431c Replacement Nut 12mm x 1.25 12 50-28451c Replacement Nut 12mm x 1.75 12 50-28441c Replacement Nut 1/ 2"-20 12 50-28461c Replacement Nut 5/ 8"-18 12 • Stainless steel fits 3/ 4" tapered shaft • Includes 5/ 8" - 18 and 1/ 2" - 20 nut 3 SPOKE SPORTS STEERING WHEEL WITH TURNING KNOB Item# Case 50-28521c 12 Easily converts existing Destroyer wheels to the most modern versions. Installation tool included. Fits Destroyer wheels only. STAINLESS TURNING KNOB Item# Case 50-28491c 12 Easily converts existing Destroyer wheels to the most modern versions. Attractive and durable black plastic center. Fits Destroyer wheels only. LARGE STAINLESS STEEL TURNING KNOB OUTBOARD HYDRAULIC STEERING LOCK In use Item# Case 50-28011c 12 • Attaches to outboard steering cylinders for trailering-reduces pressure on cylinder • Attached cord for easy removal and storage of clips • Clips are made of thermoplastic rubber • High visible color acts as a reminder to remove before use Item# Description Fastener Case 50-28401c Twin Lever Control # 10 screws 6 50-28411c Red Knob 12 50-28421c Black Knob 12 Made of chrome plated brass. Each separate lever controls clutch and throttle for one engine. Functions easily identified by red and black knobs. Designed to use 33C type control cables. Shims and cable clamps are made of brass and are supplied for easy installation. Overall height 85/ 16" Base: 45/ 16" W x 57/ 16" L x 3" H Not for dual station applications. TWIN LEVER, SINGLE STATION CONTROL Item# Qty Case 50-28501c 2 12 Pair of stainless steel and plastic pulleys with two stamped stainless steel eye straps. Maximum rope size: 1/ 4". OD of sheave: 25/ 16". 41/ 2" overall length. TILLER ROPE PULLEY Item# Qty Case 50-28601 2 12 For use with 1/ 8" or 3/ 16" rope. Chrome plated zinc. Dimensions: 11/ 4" x 11/ 16". TILLER ROPE CLAMP Item# Case 50-28131c 12 Provides a weatherproof tilt control system at the stern area of the boat. Can be used for remote adjustment of hydraulic plates. 18" Marine grade tinned wiring harness included. TRANSOM TRIM CONTROL Item# Qty Case 50-90391 2 12 • Cleans tilt tubes • For use with electric drills • Sold in pairs STEERING TUBE CLEANING BRUSH Item# Size Case 50-28251 7/ 8" 12 50-28261 1" 12 The Steering Guard should be installed on all cable and sidemounted hydraulic steering systems to lubricate, clean and seal the system. Will more than double the life of a new cable system. Made of stainless steel. Installs in 10 minutes. Eliminates greasy steering rods forever. 28251: Fits Honda, Mercury, Mariner, Johnson, Evinrude, Nissan, Suzuki, Tohatsu, Yamaha and Force with 7/ 8" thread. 28261: Fits Honda, Mercury, and Mariner with 1" thread. STEERING GUARD Item# Case 50-28301c 10 Heavy-duty rubber boot to fit over output end of steering cable at engine for complete protection from elements and preventing lubrication from being washed away. Fits all standard steering cables including Morse, Teleflex, Detmar, etc. Dimensions: 1" ID steering cable end, 3/ 8" ID output end, 11/ 2" overall diameter, 10" extended length, 31/ 2" minimum length. STEERING CABLE PROTECTOR Item# Size Qty Case 50-29301c 3" 12 50-29300c 3" Bulk 24 50-29251c 4" 12 50-29250c 4" Bulk 24 Seals off water intake and protects cables, wiring and gas lines. Made of durable vinyl plastisol. MOTORWELL BOOT 29301 29251
RkJQdWJsaXNoZXIy MTI2MTky